Pneumatic Dual Fluid Injection Pump With Three Pumps
|Payment Type:||L/C,T/T,D/P,Paypal,Money Gram,Western Union|
|Terms of Trade:||FOB,CFR,CIF,FCA,CPT|
|Min. Order:||1 Set/Sets|
|Delivery Time:||20 Days|
|Packaging:||in carton or wooden package or export standard package|
|Place of Origin:||SHANDONG|
Pneumatic Dual Fluid Injection Pump With Three Pumps
Pneumatic double - fluid injection pump accessories product introduction
3 zbqs12/10 mine pneumatic dual fluid injection pump grouting pump accessories are set multidisciplinary advanced technology developed a new kind of grouting equipment, mainly used in mines, tunnels, water and electricity, the subway, building, bridge construction project, pneumatic dual fluid injection pump is used for crushing rock grouting consolidation, water plugging and fill the gap of engineering construction;Eliminate the underground hidden danger in flood fighting and rescue.Mine pneumatic dual fluid injection pump accessories with compressed air as power source, because of the cylinder and cylinder has great effect of the grouting area ratio, with smaller pressure can make the grouting cylinder produces high grouting pressure.Each cylinder vertical arrangement, and the stress condition is good, the reciprocating movement of the cylinder adopts advanced built-in control valve, bidirectional drive, safe and reliable, the volume rate is greatly increased, low gas consumption, energy saving effect is remarkable, the grouting cylinder as the single pole double-acting cylinder, which can realize continuous slurry, compressed oxygen self-rescuer,slurry mixing, grouting pressure fluctuation is small.we can supply the air cannon , pneumatic diaphragm ,electrical machinery.
Technical characteristics of pneumatic double fluid injection pump fittings
Outstanding advantages of this series of grouting pumps: advanced structure, high rated grouting pressure, high efficiency, convenient movement and maintenance;High pressure, large displacement is a multi - function pump.
Complete function. It can be filled with either a single group of slurry or a double group of slurry.Both chemical slurry can be injected and cement slurry can be injected.Each cylinder works synchronously, mixing ratio can be adjusted, mixing slurry is even, still can act as emulsion pump or high pressure pump, hydraulic pump and so on, used for other occasions.underground mining rail car,coal mining tunnel locomotive .
Good safety. It can be used safely in places with high variations in inflammable, explosive, temperature and humidity.mine car arrester
According to the different needs of customers to adjust parameters, meet different pressure, flow, multicomponent slurry mixing ratio and the special requirements of different media: can work three cylinder or cylinder can realize 4:1 or slurry mixing ratio of 1:1.
Main Technical Parameters
Diameter for air in
Diameter for seriflux in
Diameter for seriflux out
1. Inlet pipe
2. Inlet pipe another thing
3. Pressure gauge assembly
4. Pump bracket
6. Reciprocating pneumatic motor
7. Injection cylinder assembly
8. Pass valve
9. Steel wire hose
10. Suction slurry head
11. High pressure direct valve
12. Mixer assembly
Structural characteristics and working principle of pneumatic dual-fluid injection pump accessories
Mine pneumatic dual fluid grouting pump accessories with compressed air as power source, because of the cylinder and cylinder has great effect of the grouting area ratio, with smaller pressure can make the grouting cylinder produces high grouting pressure.
Each cylinder vertical arrangement, and the stress condition is good, the reciprocating movement of the cylinder adopts advanced built-in control valve, bidirectional drive, safe and reliable, the volume rate is greatly increased, low gas consumption, energy saving effect is remarkable, the grouting cylinder as the single pole double-acting cylinder, which can realize continuous slurry, slurry mixing, grouting pressure fluctuation is small.
Pneumatic dual - fluid injection pump maintenance instructions
Be sure to remove 3 screws from the fixed pressure gauge (1.6mpa) on the cover, remove the PU pipe behind the pressure gauge, and remove 8 screws from the cover before removing the cover.
Screw down the nut that fixed the grouting tank, and then screw down the nut that fixed the grouting cylinder piston rod and piston rod drive block.
3, the grouting cylinder screw on cap unscrewing, large (small) into the first pulp box from large (small) grouting can be removed, must take out large (small) into pulp after mouth sealing washer, then the piston rod pumped from grouting cylinder, otherwise easy to damage the piston sealing ring.
Unscrewed the large (small) grouting cylinder screw cover, take out the piston rod, on the other side with special nylon rods or copper bar, the piston rod combination ring (axis) from grouting cylinder ejector (small circle grouting cylinder assembly is the small piston rod combination (axis) from grouting cylinder ejector).
Special attention should be paid to the installation direction when replacing the sealing rings of the grouting cylinder, and the sealing rings should not be damaged.
Remove the four nuts of the upper cover of the cylinder and open the cylinder.
Remove the screw from the upper cover of the cylinder to open all components of the pneumatic valve.
Pneumatic double fluid injection pump equipment maintenance
Good maintenance is the prerequisite to ensure the normal operation of the equipment and to extend the service life.Regularly add lubricating oil to the lubricating point of grouting pump for tightening, adjustment and maintenance.After proper maintenance, the catalyst hose should be replaced after about 10 tons of grouting materials are used.About 20 tons of grouting material will require replacement of worn piston parts and seals.
Jining Dongda Electromechanical Co.,Ltd.
Shandong Dongda Group subordinate enterprises includes Shandong Kuangan electromechanical Co.,Ltd Jining Dongda electromechanical Co.Ltd,Jining Dongda Electric Co., Ltd . Dongda Group is located in the "Hometown of Confucius and Mencius," the Jining City, Shandong Province. With registered capital of RMB 11.18 million and the area of 80,000 square meters, the group owns total assets of RMB 200 million .With strong technical force, adhere to the idea--- science and technology is the first productivity, quality is life, the existing staff more than 500 people. It has developed to a comprehensive company with annual production increased to billions. Dongda Group has 10 series, more than 70 products. Including mines lifting equipment, transport equipment, communication signal equipment, personal-protective equipment, ventilation equipment, mining cleaning equipment, supporting equipment, drilling machines and accessories, mining pump, electrical equipment, lighting equipment ,rock drilling equipment and other products. Now ,hundreds kinds of products have been exported to more than 60 Countries and regions. Such as USA, Australia, Russia, Canada, Middle East, Africa etc Dongda Group has succeeded in passing a number of certification systems which are ISO9001, 2008 quality management system certification, CE certification ,Alibaba GIS certification, SGS certification (made in China) . With excellent quality and competitive price , Dongda group is to establish long-term, broader economic and trade cooperation and strategic partnership with a number of large state-owned enterprises and customers, and won the unanimous approval of them.
- Company Name: Jining Dongda Electromechanical Co.,Ltd.
- Representative: Sun Hua
- Product/Service: Coal Mine Equipment , Coal Feeder , Hoop Directing Device , Diaphragm Pump , Electric Pump , Electric Winch
- Capital (Million US $): 30000000
- Year Established: 2004
- Total Annual Sales Volume (Million US $): Below US$1 Million
- Export Percentage: 21% - 30%
- Total Annual Purchase Volume (Million US $): US$1 Million - US$2.5 Million
- No. of Production Lines: 5
- No. of R&D Staff: 11 -20 People
- No. of QC Staff: 11 -20 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): 50,000-100,000 square meters
- Factory Location: JINZOU ZONE,HIGH-TEC DISTRICT,JINING CITY,SHANDONG PRVINCE ,CHINA
- Contact Person: Mr. kevin
- Tel: 86-537-2902388
Premium Related Products